Pentium III: Revizyonlar arasındaki fark
[kontrol edilmiş revizyon] | [kontrol edilmiş revizyon] |
İçerik silindi İçerik eklendi
{{Türkçe değil}} etiketi eklendi article (TW) |
|||
23. satır:
| numcores = 1
}}
'''Pentium III''' işlemciler [[intel]]32x86 masaüstü ve [[mikroişlemci]]leri destekler. 26 Şubat
[[Pentium II]] tabanlı işlemcilerle çok benzerdir. Aralarındaki en büyük fark Pentium 3 işlemcilerin ek olarak [[SSE]] buyruk kümesi kullanmasıdır. SSE ile Pentium 3, 70 adet yeni komut sunar. Bu komutlar sayesinde 3 Boyutlu [[grafik]], [[ses]] ve multimedya uygulamalarında yüksek başarım sağlanır. Bu küme 3 boyutlu grafik ve media işlemlerinin başarımını artırmaktadır. Ayrıca Pentium 3 işlemcilerde seri numarası yongaya gömülü olarak bulundurulmaktadır. Bu özellik, Internet e-ticaret üzerinde güvenli uygulama için geliştirilmiştir.
40. satır:
=== Coppermine ===
25 Ekim
0.18 mikron teknolojisi ile Coppermine tamamen Katmaiden ayrılır ve daha iyi bir başarım gösterir. Çekirdek voltajı da bu sayede 2.0V’dan 1.65V’a indirilmiştir.
69. satır:
==Pentium III's SSE implementation==
[[Dosya:Pentium III on motherboard.jpg|thumb|Pentium III CPU mounted on a motherboard]]
Since Katmai was built in the same 0.25 µm process as Pentium II "Deschutes", it had to implement SSE using as little silicon as possible. To achieve this goal, Intel implemented the 128-bit architecture by double-cycling the existing 64-bit data paths and by merging the SIMD-FP multiplier unit with the x87 scalar FPU multiplier into a single unit. To utilize the existing 64-bit data paths, Katmai issues each SIMD-FP instruction as two μops. To compensate partially for implementing only half of SSE’s architectural width, Katmai implements the SIMD-FP adder as a separate unit on the second dispatch port. This organization allows one half of a SIMD multiply and one half of an independent SIMD add to be issued together bringing the peak throughput back to four floating point operations per cycle — at least for code with an even distribution of multiplies and adds.<ref>Diefendorff Keith ([[March 8]],
The issue was that Katmai’s hardware-implementation contradicted the parallelism model implied by the SSE instruction-set. Programmers faced a code-scheduling dilemma: Should the SSE-code be tuned for Katmai's limited execution resources, or should it be tuned for a future processor with more resources? Katmai-specific SSE optimizations yielded the best possible performance from the Pentium III family, but was suboptimal for later Intel processors, such as the Pentium 4 and Core.
82. satır:
* [[Front side bus]]: 100, 133 MHz
* VCore: 2.0 V, (600 MHz: 2.05 V)
* Piyasaya Çıkış Tarihi: 17 Mayıs
* Saat Sıklığı: 450-600 MHz
** 100 MHz FSB: 450, 500, 550, 600 MHz
94. satır:
* [[Front side bus]]: 100, 133 MHz
* VCore: 1.6V, 1.65V, 1.70V, 1.76V (cD0, see below)
* Piyasaya Çıkış Tarihi: 25 Ekim
* Saat Sıklığı: 500 - 1133 MHz
** 100 MHz FSB: 500, 550, 600, 650, 700, 750, 800, 850, 900, 1000, 1100 MHz (E-Models)
125. satır:
The Pentium III was the first CPU to include an unique, retrievable, identification number, called PSN (Processor Serial Number). A Pentium III's PSN can be read by software through the [[CPUID]] instruction if this feature has not been disabled in [[BIOS]].
On [[November 29]]
Eventually Intel decided to remove the PSN feature on Tualatin-based Pentium IIIs, and the feature was not carried through to the Pentium 4 or Pentium M.
|